LG 4922W5A057G dimensions - Revision history

Lensovet: power hole updates

2024-11-18T04:51:40Z

power hole updates

Lensovet: use fraction symbols where possible

2024-11-17T22:25:46Z

use fraction symbols where possible

Lensovet: Created page with "I purchased an open-box LG microwave oven which did not include the upper or wall mounting templates. It seemed silly to spend $20 for a piece of paper, so thanks to a [https:..."

2024-11-17T22:23:34Z

Created page with "I purchased an open-box LG microwave oven which did not include the upper or wall mounting templates. It seemed silly to spend $20 for a piece of paper, so thanks to a [https:..."

New page

I purchased an open-box LG microwave oven which did not include the upper or wall mounting templates. It seemed silly to spend $20 for a piece of paper, so thanks to a [https://www.youtube.com/watch?v=V7G6Na-7F0w YouTube video I found of someone else installing theirs], I was able to extract the necessary measurements.

Holes J and K for the bolts to attach the microwave to the bottom of the cabinet over it are 10 3/8" from the back wall. J (left side) is 11 7/8" from the centerline; K (right side) is 13 7/16" from the centerline. Both of these holes should be 3/8" (technically the bolts you use are 1/4", so depending on how good your tolerances are, you might be able to get away with a 1/4" hole).

The power supply hole (M) is 5 1/8" from the wall and 6 1/8" from the centerline. It is 2" in diameter.

The roof vent opening (L) is 6.5" on either side of the centerline and 4.5" for a recessed cabinet (at least 3/4" recess) or 5 3/4" for a flush cabinet.

The wall vent opening (F) is 1/4" below the bottom of the cabinet and has dimensions of 4" tall and 12" wide, 6" on either side of the centerline. The centerline should go through the ▽ symbol on the bottom mounting bracket.

Hope this helps someone!

@@ Line 3: / Line 3: @@
 Holes J and K for the bolts to attach the microwave to the bottom of the cabinet over it are 10⅜" from the back wall. J (left side) is 11⅞" from the centerline; K (right side) is 13 7/16" from the centerline. Both of these holes should be ⅜" (technically the bolts you use are ¼", so depending on how good your tolerances are, you might be able to get away with a ¼" hole).
-The power supply hole (M) is 5⅛" from the wall and 6⅛" from the centerline. It is 2" in diameter.
+The power supply hole (M) is 5⅛" from the wall and 6⅛" from the centerline. It is 2" in diameter. In my experience, the wall distance was closer to 5½" and a 1 3/16" hole was more than sufficient (I had a hole saw in that size already and used it).
 The roof vent opening (L) is 6½" on either side of the centerline and 4½" for a recessed cabinet (at least ¾" recess) or 5¾" for a flush cabinet.

@@ Line 1: / Line 1: @@
 I purchased an open-box LG microwave oven which did not include the upper or wall mounting templates. It seemed silly to spend $20 for a piece of paper, so thanks to a [https://www.youtube.com/watch?v=V7G6Na-7F0w YouTube video I found of someone else installing theirs], I was able to extract the necessary measurements.
-Holes J and K for the bolts to attach the microwave to the bottom of the cabinet over it are 10 3/8" from the back wall. J (left side) is 11 7/8" from the centerline; K (right side) is 13 7/16" from the centerline. Both of these holes should be 3/8" (technically the bolts you use are 1/4", so depending on how good your tolerances are, you might be able to get away with a 1/4" hole).
+Holes J and K for the bolts to attach the microwave to the bottom of the cabinet over it are 10⅜" from the back wall. J (left side) is 11⅞" from the centerline; K (right side) is 13 7/16" from the centerline. Both of these holes should be ⅜" (technically the bolts you use are ¼", so depending on how good your tolerances are, you might be able to get away with a ¼" hole).
-The power supply hole (M) is 5 1/8" from the wall and 6 1/8" from the centerline. It is 2" in diameter.
+The power supply hole (M) is 5⅛" from the wall and 6⅛" from the centerline. It is 2" in diameter.
-The roof vent opening (L) is 6.5" on either side of the centerline and 4.5" for a recessed cabinet (at least 3/4" recess) or 5 3/4" for a flush cabinet.
+The roof vent opening (L) is 6½" on either side of the centerline and 4½" for a recessed cabinet (at least ¾" recess) or 5¾" for a flush cabinet.
-The wall vent opening (F) is 1/4" below the bottom of the cabinet and has dimensions of 4" tall and 12" wide, 6" on either side of the centerline. The centerline should go through the ▽ symbol on the bottom mounting bracket.
+The wall vent opening (F) is ¼" below the bottom of the cabinet and has dimensions of 4" tall and 12" wide, 6" on either side of the centerline. The centerline should go through the ▽ symbol on the bottom mounting bracket.
 Hope this helps someone!